Exactly How to Install a Tub Yourself: Removing and Replacing.
Exactly How to Install a Tub Yourself: Removing and Replacing.
Blog Article
We have stumbled upon the article about A Step-by-Step Guide to Installing a Bathtub below on the internet and believe it made sense to talk about it with you over here.
Installing a bath tub isn't precisely rocket science, but it does require strong plumbing, carpentry, as well as sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a moderately challenging project. If the old bathtub is easily accessible, the task can relocate speedily; if you need to open a wall surface to eliminate the old bathtub as well as place the brand-new bathtub, the task is a lot harder. In either situation, the task is within a home handyman's abilities, although you will require a helper to leave the old tub as well as set in the brand-new one. Ensure you have certified yourself for the job and also are comfortable trying it. Instead of hiring a professional to take control of a halfway-completed job, it is far better to think about utilizing one prior to you begin. Possibilities are you may require a specialist plumber to make tube connections.
This write-up will assist you install a brand-new bath tub in your restroom if you have actually already gotten a new tub and also don't require to change the arrangement of your previous water system pipelines.
Your tools and also material list should make up the following:
Preparing for the Setup
First of all, the sustaining frame provided with the bath must be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is necessary to ensure that if the tap comes with a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps device to stop strain on the tub.
Fit the adaptable tap ports to the bottom of both faucets using 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet through the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you use all of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should now prepare to be suited its final setting.
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you need to do is disconnect the water supply. After doing so, switch on the taps to drain any type of water staying in the system. The procedure of eliminating the existing taps can be quite problematic due to the restricted gain access to that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the taps. Have a cloth ready for the staying water that will come from the pipes. Once the supply pipes have actually been gotten rid of, make use of the very same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from transforming throughout this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any type of old securing substance.
Prior to carrying on to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Installing the Bathtub
Using both wood boards under its feet, position the tub in the needed setting. The wooden boards are valuable in uniformly spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto four small factors.
The following objective is to guarantee that the tub is leveled all round. This can be achieved by examining the level and also changing the feet on the tub till the spirit level reads level.
To mount faucets, fit all-time low of the furthest flexible faucet connector to the appropriate supply pipeline by making a compression join; after that do the exact same for the other faucet.
Turn on the water supply and also inspect all joints and new pipework for leakages as well as tighten them if necessary. Fill up the bathtub and likewise examine the overflow outlet and also the typical electrical outlet for leaks.
Ultimately, deal with the bath paneling as explained in the manufacturer's user's manual. Tiling and securing around the tub must wait up until the bathtub has actually been used a minimum of once as this will resolve it into its final placement.
Fitting New Touches
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic port to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a link to the current supply pipelines.
If you require to fit a monobloc, then you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the faucet in the mounting hole in the bath/basin ensuring that the washers remain in area between the tap as well as the sink. Safeguard the faucet in position with the manufacturer offered backnut. As soon as the faucet is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with regular faucet ports. The previous kind should be linked to the tap finishes first, tightening just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the location where the bath meets the tile, it is required to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate enough to crack a rigid seal, triggering the water to permeate the wall surface in between the bathroom and also the tiling, bring about problems with moisture as well as feasible leakages to the ceiling below.
You can select from a range of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and cartridges, and are capable of sealing spaces up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of soaked newspaper or soft rope. Remember to constantly load the bathtub with water prior to securing, to enable the movement experienced when the tub remains in use. The sealant can split rather very early if you do not take into consideration this movement before securing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise quickly offered on the market. It is suggested to fit the ceramic tiles utilizing water-resistant or waterproof sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you enjoyed our piece on A Step-by-Step Guide to Installing a Bathtub. Thanks for taking time to read our blog. Enjoyed reading our content? Please share it. Help someone else locate it. I value reading our article about A Step-by-Step Guide to Installing a Bathtub.
Contact Us Now Report this page